Difference between revisions of "IntegrationDaq 240628"

Latest revision as of 17:54, 28 June 2024

Back to Main Page >> Data Acquisition Meetings >> Integrating mode DAQ meetings

previous meeting << >> following meeting

Meeting information

 Meeting time:  1:00pm Eastern
 
 Zoom connection information is sent out by email; please reach out to Paul if you don't have the current link.

Agenda

• Activity updates
  • Zhongling will report on V2495 FPGA update
  • Bryan will report on MOLLERADC Trigger Sync
• General discussion

Open Issues to be followed up later

1. Discussions with M. Pitt & J. Musson to understand the beam monitor signals we'll be getting
2. Draft timing diagram: DocDB 790
3. Michael, Bob, Brynne, and Paul should put together a list of the integrator running modes we would like to have available

Minutes

Recording at zoomgov:

Participants: B. Moffit, W. Gu, P. King, R. Michaels, R. Conaway, A. Sen, K. Dehmelt, J. Pan, Z. Ji, B. Shaw, B. Blaikie, S. Kundu, M. Gericke, C. Ghosh, D. Bishop, S. Chatterjee, H. Liu

• I have made edits in the specification document, and I think that it is basically complete from my perspective.
  • Michael doesn't think he needs to add anything else to it
• Bryan & William
  • He has the two two MOLLER-ADCs connected to a VME-TI
  • He's monitoring the VME-TI trigger out, and William has a modified the ADC firmware to send the trigger signal out to the back panel output
  • They can walk the trigger as seen by the ADC by up to ~1 us, and they see the trigger time move appropriately
  • There are several firmware updates in the TI module
  • They can read out the TI trigger bank
  • He has a zmq port for the TI registers
  • There are still a few issues that Bryan and William that are still tracking down, that are inconsistencies in the firmware response.
  • These tests show the hardware is working and the signals are getting where they need to on the board
• Daryl thinks that with Bryan and William's recent work he'd be comfortable to make the final layout updates, and then we'd be ready to send out the production order
  • Daryl will make the updates within the next few weeks; Michael guesses that the production order would then go out around the end of July
• Michael asks if one of the two ADC modules could be taken up to W&M in the early fall to be used for the detector tests
  • Bryan thinks that the remainder of the synchronization tests could be finished in a month or two
    • After that point, most of the development would be to build up experience with the board to get ready for larger-scale testing
  • Maybe it is better to get a third ADC for use at W&M. TRIUMF has two and will send one of them to Michael; they'll use it for tests at Manitoba for the rest of the summer and then bring it to W&M in the fall.
• Digital BCM readout through a V2495
  • They have verified that the V2495 can decode the serial data from the digital receivers
  • They have set up an internal test where the V2495 sends a 32-bit-wide parallel data stream over a parallel cable to the decoder module.
    • This is fast enough data transfer to allow us to resolve the 10us spin flip
  • Testing of doing integration using an external gate
    • Sending two bursts of Manchester data with different time spacings.
      • With the serial transmission, the two bursts merge and the initial data burst is lost. (Note that 28 bits should take ~28us to be transmitted with the current transceiver speed on the digital receiver).
      • Either getting a higher data rate transceiver or parallel data transfer from the digital receiver would be possible to get to the 10us spin flip resolution
  • Bob had talked with Chad Seaton, and the instrumentation group thinks that a faster transceiver would be possible
• We will not have the counting DAQ meeting on 5 July; the next DAQ meeting will be the integration DAQ meeting on 12 July