Difference between revisions of "IntegrationDaq 220826"
From Moller Wiki
(Created page with "__NOTOC__ Back to Main Page >> Data Acquisition Meetings >> Integrating mode DAQ meetings In...") |
(→Minutes) |
||
| (One intermediate revision by the same user not shown) | |||
| Line 18: | Line 18: | ||
== Agenda == | == Agenda == | ||
* Activity updates | * Activity updates | ||
| − | |||
* General discussion | * General discussion | ||
| Line 27: | Line 26: | ||
== Minutes == | == Minutes == | ||
| − | Recording at zoomgov: | + | Recording at zoomgov: [https://jlab-org.zoomgov.com/rec/share/fEUUqc6aj3j-bp50XhMCNqHbnS1Bo56guNzqQIyNTkT2Ls8dfalNKHE6ScmbxL3G.Zxm5ZOAD-fozEQTt?startTime=1661529198000] |
| − | Participants: | + | Participants: W. Gu, P. King, B. Blaikie, B. Moffit, B. Shaw, D. McNulty, D. Bishop, C. Zorn, M. Gericke |
| + | |||
| + | * William has not received the integrator modules yet. Paul will check with Bob about the progress on getting the board in the chassis. | ||
| + | * Bryerton has received the register information from Bryan which is needed to test the TI-slave functionality. He plans to test it later today | ||
| + | * Daryl reports that he has not yet done the input-stage modifications for the two boards to be sent to Mainz and to Dustin. He'll get to that next week | ||
| + | * Michael has received all of the SOMs. He asks about what QA tests he should do. | ||
| + | ** He'll install them one-by-one on the ADC board and then try to boot them up, test the QSFP interfaces, and execute the test pattern mode on the ADCs. | ||
| + | * Jie has submitted another set of the base+dual amps for fabrication | ||
| + | ** These have some minor changes as compared to the previous round of prototypes. | ||
| + | ** Michael anticipates that this would be the last round of prototypes tested solely at Manitoba. They would go out to other collaborators for further testing and feedback | ||
| + | ** After the meeting, Michael sent an email out to the detector list to see how many to make, and who would like to get some for testing. | ||
Latest revision as of 19:26, 26 August 2022
Back to Main Page >> Data Acquisition Meetings >> Integrating mode DAQ meetings
previous meeting << >> following meeting
Meeting information
Meeting time: 12:00pm Eastern Zoom connection information Join ZoomGov Meeting https://jlab-org.zoomgov.com/j/1603800887?pwd=aXVmSnN6aWZWN3RBdXB4RUhGckZJdz09 Meeting ID: 160 380 0887 Passcode: 903612 US Tool free phone: (833) 568 8864 Find your local number: https://jlab-org.zoomgov.com/u/ab8341cjcG
Agenda
- Activity updates
- General discussion
Open Issues to be followed up later
- Discussions with M. Pitt & J. Musson to understand the beam monitor signals we'll be getting
- Draft timing diagram: DocDB 790
- Michael, Bob, Brynne, and Paul should put together a list of the integrator running modes we would like to have available
Minutes
Recording at zoomgov: [1]
Participants: W. Gu, P. King, B. Blaikie, B. Moffit, B. Shaw, D. McNulty, D. Bishop, C. Zorn, M. Gericke
- William has not received the integrator modules yet. Paul will check with Bob about the progress on getting the board in the chassis.
- Bryerton has received the register information from Bryan which is needed to test the TI-slave functionality. He plans to test it later today
- Daryl reports that he has not yet done the input-stage modifications for the two boards to be sent to Mainz and to Dustin. He'll get to that next week
- Michael has received all of the SOMs. He asks about what QA tests he should do.
- He'll install them one-by-one on the ADC board and then try to boot them up, test the QSFP interfaces, and execute the test pattern mode on the ADCs.
- Jie has submitted another set of the base+dual amps for fabrication
- These have some minor changes as compared to the previous round of prototypes.
- Michael anticipates that this would be the last round of prototypes tested solely at Manitoba. They would go out to other collaborators for further testing and feedback
- After the meeting, Michael sent an email out to the detector list to see how many to make, and who would like to get some for testing.
